열-기계적 피로하중을 받는 균열시편 제작시간 단축에 관한 연구
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국전산구조공학회
ㆍ수록지정보 : 한국전산구조공학회 논문집 / 21권 / 1호
ㆍ저자명 : 이규범, 최주호, 안대환, 이보영
ㆍ저자명 : 이규범, 최주호, 안대환, 이보영
한국어 초록
원자력발전소에서는 열교환 파이프에서 발생하는 열피로 균열을 비파괴 탐상장비를 이용하여 조기에 발견하는 것이 안전을 위해 매우 필요하며, 따라서 이를 모사한 인공균열시편 제작에 많은 노력을 기울이고 있다. 그러나 이러한 균열은 일반 기계가공으로 제작하는 것이 불가능하여 실제 조건과 유사한 열 반복하중 하에서 제작될 수밖에 없는데, 이를 위해 많은 시간이 소요된다. 본 연구에서는 크랙성장 시뮬레이션 기법을 이용하여 이러한 균열 제작시간을 단축하기 위한 최적의 열하중 조건을 찾고자 하였다. 이를 위해 임의조건에서 시뮬레이션 및 열피로균열 발생 기초실험을 수행하여 균열 초기수명과 진전수명을 검증하였고, 이를 바탕으로 다양한 가열 및 냉각시간을 시뮬레이션 함으로써 제작시간을 최소화하는 열하중 조건을 구하였다. 시뮬레이션에서는 응력해석을 위해 상용 소프트웨어 ANSYS를 초기균열수명 계산을 위해 수치계산용 소프트웨어 ZENCRACK을 이용하여 코딩을 균열진전수명 평가를 위해 ZENCRACK 소프트웨어를 이용하였다. 그 결과 1mm 균열 제작에 소요되는 시간은 초기의 418시간에서 319시간으로 24% 단축되는 것으로 예측되었다.영어 초록
In the nuclear power plant, early detection of fatigue crack by non-destructive test (NDT) equipment due to the thermal cyclic load is very important in terms of strict safety regulation. To this end, many efforts are exerted to the fabrication of artificial cracked specimen for practicing engineers in the NDT company. The crack of this kind, however, cannot be made by conventional machining, but should be made under thermal cyclic load that is close to the in-situ condition, which takes tremendous time due to the repetition. In this study, thermal loading condition is investigated to minimize the time for fabricating the cracked specimen using simulation technique which predicts the crack initiation and propagation behavior. Simulation and experiment are conducted under an initial assumed condition for validation purpose. A number of simulations are conducted next under a variety of heating and cooling conditions, from which the best solution to achieve minimum time for crack with wanted size is found. In the simulation, general purpose software ANSYS is used for the stress analysis, MATLAB is used to compute crack initiation life, and ZENCRACK, which is special purpose software for crack growth prediction, is used to compute crack propagation life. As a result of the study, the time for the crack to reach the size of 1mm is predicted from the 418 hours at the initial condition to the 319 hours at the optimum condition, which is about 24% reduction.참고 자료
없음태그
"한국전산구조공학회 논문집"의 다른 논문
- 프로세스 분할 병행에 의한 통합 구조설계 운용12페이지
- 콘크리트 전단벽 아웃리거의 두께 산정9페이지
- 활하중 분배계수식 개발을 위한 I형 프리스트레스트 콘크리트 거더 교량의 구조해석 모델11페이지
- Vibration-Based Monitoring of Prestress-Loss in PSC Gir..8페이지
- Regularization Method by Subset Selection for Structura..10페이지
- Distributed Hybrid Simulation and Testing System using ..13페이지
- 계면손상과 미세균열을 고려한 입자강화 복합재료의 미세역학 탄성구성모델8페이지
- 볼트의 변형을 고려한 강재 조립 합성보의 휨거동8페이지
- 직접탐색을 이용한 유전자 알고리즘에 의한 RC 프레임의 최적설계14페이지
- 기능경사 소재 등가 물성치 예측을 위한 균질화 기법의 특성분석을 위한 수치해석8페이지