3차원 유한요소 해석을 통한 압전에너지 도로의 장기 공용성 예측
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국도로학회
ㆍ수록지정보 : 한국도로학회논문집 / 19권 / 5호
ㆍ저자명 : 김현욱, 남정희, 최지영
ㆍ저자명 : 김현욱, 남정희, 최지영
영어 초록
PURPOSES : The piezoelectric energy road analysis technology using a three-dimensional finite element method was developed to investigate pavement behaviors when piezoelectric energy harvesters and a new polyurethane surface layer were installed in field conditions. The main purpose of this study is to predict the long-term performance of the piezoelectric energy road through the proposed analytical steps. METHODS: To predict the stresses and strains of the piezoelectric energy road, the developed energy harvesters were embedded into the polyurethane surface layer (50 mm from the top surface). The typical type of triaxial dump truck loading was applied to the top of each energy harvester. In this paper, a general purpose finite element analysis program called ABAQUS was used and it was assumed that a harvester is installed in the cross section of a typical asphalt pavement structure. RESULTS : The maximum tensile stress of the polyurethane surface layer in the initial fatigue model occurred up to 0.035 MPa in the transverse direction when the truck tire load was loaded on the top of each harvester. The maximum tensile stresses were 0.025 MPa in the intermediate fatigue model and 0.013 MPa in the final fatigue model, which were 72% and 37% lower than that of the initial stage model, respectively. CONCLUSIONS : The main critical damage locations can be estimated between the base layer and the surface layer. If the crack propagates, bottom-up cracking from the base layer is the main cracking pattern where the tensile stress is higher than in other locations. It is also considered that the possibility of cracking in the top-down direction at the edge of energy harvester is more likely to occur because the material strength of the energy harvester is much higher and plays a role in the supporting points. In terms of long-term performance, all tensile stresses in the energy harvester and polyurethane layer are less than 1% of the maximum tensile strength and the possibility of fatigue damage was very low. Since the harvester is embedded in the surface layer of the polyurethane, which has higher tensile strength and toughness, it can assure a good, long-term performance.참고 자료
없음태그
"한국도로학회논문집"의 다른 논문
- 도로품질 향상을 위한 야간 도로공사 시간확대의 영향분석10페이지
- 가상주행 시뮬레이터를 활용한 시선유도시설 효과평가 연구9페이지
- 몬순기후형 중온 개질 아스팔트 혼합물의 역학적 물성 평가 연구11페이지
- 성별에 따른 주·야간 원형교차로 사고모형9페이지
- 일반국도의 가열 재활용 아스팔트 포장 공용수명 분석 연구13페이지
- 원더링 분포를 고려한 도로포장 평탄성 지수의 가중치 산정기법 개발8페이지
- 소형 시뮬레이터를 이용한 차량거동요소별 승차감 민감도 평가10페이지
- 도로동공 탐지에 적합한 GPR 타입 선정에 관한 연구7페이지
- 결합재 타입 및 구성비 변화에 따른 시멘트 페이스트의 레올로지 특성 분석12페이지
- 서울형 포장설계식 개선 및 검증10페이지